Install XP From USB


How to start-
1. First make sure you have a properly formatted USB disk or flash media.
It must have a MBR and an active partition set.

a) USB flash media- format it with RMPrepUSB selecting "Boot as HDD" and "XP bootable" options.
Note that it will DELETE all partitions. NTFS is reported faster on some systems, your USB stick parameters are also factor. Whereas NTFS generally is not recommended for USB flash media, if you are not planning excessive usage, but rather occasional installs from it, then it should be safe to use it as long as you can boot from it.There is another way to format USB flash media- to use filter driver, such as Hitachi microdrive filter driver or dummydisk.sys (included, look in FILES\MULTIpartitionUSBstick folder). Using such driver will 'make' your stick to appear to Windows as fixed disk. In this case, when formatting Windows will write MBR on in with partition information.
You may now use Disk management console, or third party programs to make multiple partitions and format them as you desire.NTFS performs way faster on some systems, or with some USB sticks. However, keep in mind that depending on usage and USB stick quality, it may "wear it out" quicker.

!!!Make sure you set an active partition, either from Disk management, or from your favourite external program if you don't have such!!!
!!!Use primary partitions when placing Windows based sources!!!
!!!Usew first partition when copying Windows XP/2003/2000 Setup!!!

b) USB hard disk- format it from within Windows and make sure you set active partition!!!
In both cases USB boot is not guaranteed! That depends on your BIOS/motherboard, how disk is formatted and what file system etc.In general FAT16 is the best bet for compatibility, next is FAT32, then NTFS. In some cases different format tools may set improper geometry.


2. Select your sources
a) Windows- select the folder, which contains I386/AMD64 folders. Do NOT select folder I386 itself!
!!!If you used Nlite to slim it down, option "Operating System Options-->Manual Install and Upgrade for removal" must NOT be selected. This is crucial part.!!!

Optionally:
b) BartPE/WinBuilder/UBCD4Win/WinFLPC- select the folder, which contains I386 folder.
!!!In case of WinFLPC keep in mind that BOOT.INI on target disk wll be set incorrectly!!! In order to start it for a first time, either edit in BOOT.INI disk(z) to disk(z-1) from BartPE for example, or add this to menu.lst on the active partition of the USB disk
####
title Start WinFLPC
map (hd1) (hd0)
map --hook
rootnoverify (hd0,0)
chainloader /ntldr
###
Above example assumes WinFLPC is on first partition of your first internal disk. Ammend accordingly.
Once in WinFLPC, edit BOOT.INI on the internal disk as was mentioned above:
multi(0)disk(0)rdisk(1)partition(1)\WINDOWS="Microsoft Windows FPLC" /FASTDETECT to
multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Microsoft Windows FPLC" /FASTDETECT

c) Vista / Windows 7 setup- select the folder with BOOT and SOURCES folders.
d) PartedMagic- where ISO file pmagic-3.X.iso is. You need to extract pmagic-grub4dos-3.X.iso.zip somewhere and point to its location.
To get PartedMagic: http://partedmagic.com/
e) SysLinux- select your Linux distro, which boots off SysLinux. All files/folders will be copied. A file(syslin.dat), containing Syslinux bootsector will be made, and an entry in the boot menu (menu.lst), pointing to that file will be made. In case you do not select anything only syslin.dat and ldlinux.sys will be copied, plus entry in menu.lst.
!!! Make sure you have not already added another source, which contains the same folders in root as the ones from Vista, UBCD4Win etc. The program will NOT overwrite files/folders.!!!
!!! SysLinux cannot be started from NTFS formatted partition !!!
3. Select target disk from the drop-down menu. Windows Setup can be started only from the first partition on the disk! It does not have to be active. Sorry, this is limitation from Microsoft- in case of removable USB disk, it can't read any partition than first.
If your USB disk is not shown then:
a) It's not inserted
b) It does NOT have an active partition
c) It's NOT formatted in FAT16,FAT32 or NTFS
d) The program has a bug :) Please report details.

Optional settings:
4. Force target disk type(FIXED/REMOVABLE)- usually the program will detect that for you. Force selection only if you are using filter driver as above mentioned dummydisk.sys or Hitachi microdrive filter driver. Or if for some reason the program did not detect it correctly. This is an important part when installing Windows XP/2kX from USB hard disks, or USB flash media, which is seen by Windows as FIXED.

5. Copy Setup boot files only- this option will copy just a minimal set of files (7-12MB), necessary for the first part(Text mode) of the setup.
Use to test how your USB disk boots, before copying the main part.
!!!DO NOT continue setup, you have to stop when you see the list of hard disks detected!!!

6. Test in QEMU- this will launch QEMU virtual machine, which will use your USB disk as it's internal disk. You may use that as a basic test how the build went.
Note that this not guarantees you the same result on real hardware.
!!! Currently it's setup to use 256MB RAM when started. Make sure you have at least that amount + some extra RAM available!!!
!!!USE AT OWN RISK. DO NOT PERFORM WRITE OPERATIONS WHILE IN QEMU!!!

7. BOOT.INI adjustments
a) First field is the directory name, where Windows will be installed to.
b) Disk Nr.- on which of your disks Windows will be installed to. For example if you have two internal disks, first is disk 0, second is disk 1.
c) Partition number- in which partition of the above selected disk Windows will be installed to.
d) Additional entries in BOOT.INI- as above, but creates additional lines in BOOT.INI with the specified data. Use it if you plan to install Windows to disks/partition/directories other than the ones above.

This data will be used to create BOOT.INI on the USB disk, with the correct settings. It will be used to start the second part (GUI mode) of setup, AND to start Windows for first time, still using the USB disk as boot device.

!!!Make sure the above entries are correct, otherwise you will get error messages like "HAL.DLL/NTOSKRNL.EXE was not found"
I need to stress on that- make sure BOOT.INI data is correct, and DO NOT UNPLUG the USB disk until you enter first normal Windows desktop.

8) Press GO button, you have guessed that :)

You have 2 steps, in both USB stick is your boot device (change that preferably in BIOS):
-Text mode part of setup
-GUI mode part of setup

!!!If your source is NOT Windows XP2 SP2 or SP3, some of the compressed files in ~LS folder will be deleted during the first part(Text mode). To make another install from this disk you have to copy the missing files, use the program for this purpose and follow the prompts when it finds existing setup folders.!!!

and make sure you have a driver for your mass storage (SATA/AHCI/SCSI/RAID) controller in your source.

Install Windows 7 From USB


That need to be prepared:
  1. Flashdisk 4GB
  2. DVD installer windows 7
The steps are as follows:


  1. Plug the USB stick into your computer with XP,Vista or Win7 Operating systems.
  2. Open The Command Prompt (right click if u use Win7 and Run as administrator)
  3. Type "diskpart"
  4. Type "list disk"
  5. Type "select disk x" (where x = number of disks)
  6. Type "clean"
  7. Type "create partition primary"
  8. Type "select partition 1"
  9. Type "active"
  10. Type "format quick fs=ntfs"
  11. Type "assign"
  12. Type "exit"
  13. Insert your Windows 7 installer to DVD Rom
  14. Type "f:" (where 'f' is your DVD drive)
  15. Type "cd\boot"
  16. Type "bootsect /nt60 g:" (where 'g' is your USB Tumbdrive)
  17. Type "cd.."
  18. Type "xcopy f:*.* /s/e/f g:"
  19. Thats it...considerate done..!!!

Selasa, 18 Oktober 2011

Mengatasi Blink pada Printer HP Deskjet 1050 (J410a)



Bagi anda yang pernah mempunyai printer HP Deskjet 1050 yang ngeblink, dimana lampu indikator berkedip terus tanpa bisa digunakan, maka kali ini anda akan dapat cara mengtasinya. Sama dengan printer lainnya, HP Deskjet 1050 ini pun tidak luput dari kejadian blink atau lampu indikator led berkedip terus dan printer  tidak bisa digunakan. Apakah printer HP juga butuh direset??
Sebenarnya printer yang membutuhkan reset baik secara manual maupun software eepromnya hanya ada 2, yaitu Printer merk CANON dan EPSON. Sedangkan untuk Printer HP lainya itu tidak membutuhkan reset, karena tidak ada proteksi terhadap board atau pun catridge printer HP ini. Blink pada Printer HP 1050 ini merupakan tanda bahwa salah satu dari cartridge printer HP Deskjet tersebut mengalami kerusakan chip dan harus diganti dengan cartridge yang baru.
Cara mengatasi blink HP Deskjet 1050 :
1.      Misalkan, catridge warnanya yang anda curigai rusak, ambil catridge hitamnya dan biarkan hanya catridge warnanya yang terpasang.
2.      Setelah itu, hidupkan Printer HP Deskjet anda.
3.      Kemudian amati lampu indikator power atau tintanya, kalau printer HP Deskjet 1050 anda masih blink, berarti cartridge warnanya rusak. Akan tetapi kalau lampu indikator tinta atau power nyala penuh, berarti cartridge warna printer HP Deskjet anda masih bagus.
4.      Kemudian ambil catridge warna dan pasang kembali catridge hitamnya, berarti hanya catridge hitam yang terpasang pada printer HP Deskjet anda.
5.      Kemudian amati lampu indikator power atau lampu indikator tinta yang berada pada printer HP Deskjet tersebut. Kalau masih blink lagi berati catridge hitam printer HP Deskjet anda rusak. Akan tetapi jika lampu indikator tinta atau lampu indikator power  nyala penuh, berarti catridge hitam printer HP Deskjet anda masih bagus.
Jadi kesimpulannya, printer HP Deskjet blink itu disebabkan oleh cartridge yang rusak, bukan karena minta direset.

Kalau catridge printer HP Deskjet anda rusak anda dapat mencoba membersihkan dulu pin pada catridge dengan menggunakan penghapus pensil. Kalau masih blink, berarti anda perlu mengganti catridge printer tersebut. Printer HP Deskjet bisa berfungsi hanya dengan menggunakan 1 cartridge saja. Baik catridge hitam maupun catridge warna saja. Terserah anda.
                                                      
Demikian cara mengatasi blink pada printer HP Deskjet 1050. Cara ini belaku juga untuk printer HP Deskjet D2566, 2466, 3920, 3440, dan 3535. Semoga bermanfaat…!!!!
Diposting oleh di

5 komentar:

  1. Anonim4 Juni 2013 pukul 05.15

    mau nanya nih....
    kalau ada laporan tinta habis dan sudah di isi ulang , Bagaimana cara mengatasinya

    BalasHapus
  2. Unknown16 Mei 2015 pukul 15.29

    Terimah Kasih Ilmunya yg anda telah sampaikan.................smg tetap berkarya selalu

    BalasHapus
  3. mithun30 Agustus 2016 pukul 03.14

    Really awesome blog. Your blog is really useful for me. Thanks for sharing this informative blog. Keep update your blog.


    123 HP PS 5520 Setup - 123.hp.com/ps5520

    BalasHapus
  4. Rocky12 Agustus 2017 pukul 01.40

    Wonderful blog & good post.Its really helpful for me, awaiting for more new post. Keep Blogging!

    123.hp.com/dj1117

    BalasHapus
  5. Unknown31 Juli 2018 pukul 15.58

    Mau nanya bang, sy hbis beli catridge hitam dan warna, keduanya baru tp print hp djet1050 sy lampunya masih nyala semua,trmasuk tombol power berkedip2.
    Cara atasix gmn bang???

    BalasHapus

Langganan: Posting Komentar (Atom)